![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2191-e1541890819743.jpg\")
<\/p>\n<\/p>\n
<\/p>\n
Having failed to get to Syncropendence, we thought it would be a good idea to put up our new awning (that we’d intended to take with us) and possibly install the bits of plastic sheet in the pole tube bases to protect the inflatable poles from our cat.<\/p>\n
After a lot of pumping, the tent is still on the ground.<\/p>\n
So we check the valve, pump and tent instructions (checking the instructions must be bad), all to no avail, so we contact the suppliers, we are given a few things to check and the manufacturer’s details.<\/p>\n
Followed the supplier’s instruction, still no tent, so contacted the manufacturer for more things to look at, including tightening the inflation point and the pressure relief valve, as apparently, they only put it in hand-tight in the factory.<\/p>\n
The valve and inflation point are now very tight, lots more pumping, but the tent is still on the ground, poles will not inflate, so at this point, a new set of poles is requested.<\/p>\n
Fast forward a few days, and the new poles arrive. Back out in the garden, we turn the tent inside out to remove damaged poles. It\u2019s at this point we find the second valve on the inside of the tent marked \u201cdeflation only\u201d in the open position.<\/p>\n
The suppliers and manufacturers were very helpful and did try to help, the replacement air tubs being sent very quickly; however, it\u2019s a shame the instructions didn’t mention, and the suppliers and manufacturers didn\u2019t know that there is a second valve only accessible from the inside, even the sales info states a single inflation point.
\nValves now all closed, the poles are inflating properly<\/p>\n
So, at last, we can install the plastic sheeting in the tube bases and cat-proof the tent.<\/p>\n
<\/p>\n
Reason for tent mobs (anything new has to be investigated).<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2193.jpg\")
<\/p>\n
White PTFE 0.3mm Sheet cut to size, the hole for the valve and corners rounded. The valve was removed so the plastic sheet could be put in position.<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2196.jpg\")
<\/p>\n
Plastic sheet in position.<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2194.jpg\")
<\/p>\n
Valve reassembled, just need to do up the zip on the air pole.<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2197.jpg\")
<\/p>\n
The same process for the other valves and other corners, two with no holes and one with a double hole. I may need to put a stitch at the top and bottom of the plastic sheets if they are prone to movement.<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2199.jpg\")
<\/p>\n
I’ve also replaced the cable ties on the zips with string so they can be accessed easily.<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2189.jpg\")
<\/p>\n
<\/p>\n
The Awning<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2018\/07\/IMG_2212.jpg\")
<\/p>\n
I’m quite pleased with the tent, although still to use it in anger. I will write a review<\/a> for the blog when I eventually do.
\nI’m hoping that having the air poles will not be damaged if exposed to strong winds if\/when left unattended.
\nThe PTFE plastic sheeting was sourced from eBay and appears to be cat claw proof in testing (only tested with above mention cat). I hope this is of use to someone.<\/p>\n
![\"\"](\"https:\/\/www.thebeast.blog\/wp-content\/uploads\/2020\/05\/avatar-d.jpg\"){kind=avatar}